Sometimes a heating and air conditioning system just needs to be repaired rather than completely replaced. You may need air conditioning repair services if there is leaking around the outside unit, the air coming into the house isn't hot or cool enough, the unit is short-cycling or constantly turning on and off, using the system is consistently resulting in higher-than-normal energy bills, or if there is excessive noise during startup and operation.
Once warm air inside your home blows across the indoor evaporator coil, its heat energy transfers to the refrigerant inside the coil. That transfer, in turn, “cools” the air. The refrigerant is pumped back to the compressor where the cycle begins again. The heat absorbed by the refrigerant is moved outside your home while cooled air is blown inside. Moisture that contributes to humidity is also condensed out of the air. Your cooling system is usually combined with your central heating system because they share the same ductwork for distributing conditioned air throughout your home.
Our experienced, fully certified team is familiar with a wide range of makes and models, so no matter what type of HVAC system you might have, if it’s not working as it should, we can help. We are committed to fast, accurate diagnosis and speedy, high-grade repairs that restore your HVAC system to full function. We make sure we leave your home as we find it and that you’re clear on what the problem is and what options there are for its resolution – this puts you in control of all the work we complete.
Whether it's heat repair issue, a heat pump issue or furnace problem you're facing, we provide our Leesburg and Ashburn residents and businesses full heat pump and furnace service repairs in a professional and prompt manner. We pride ourselves on employing only premier technicians to provide you with home and central heating repair service. Operators are standing by to take your call.
Air conditioning and refrigeration are provided through the removal of heat. Heat can be removed through radiation, convection, or conduction. Refrigeration conduction media such as water, air, ice, and chemicals are referred to as refrigerants. A refrigerant is employed either in a heat pump system in which a compressor is used to drive thermodynamic refrigeration cycle, or in a free cooling system which uses pumps to circulate a cool refrigerant (typically water or a glycol mix). Furnace Repair Click Here
*We work on all brands: Adams, Aire-Flo, Amana, Arcoaire, Armstrong, Beutler, Bryant, Carrier, Centurion, Coleman, Comfortmaker, Cozy, Daikin, Day & Night, Dayton, Ducane, Emerson, Empire, Evcon, Fedders, Friedrich, Frigidaire, Fujitsu, Gaffers & Statler, General Electric, Gibson, Goldstar, Goodman, GMC, Haier, Heil, Honeywell, Intertherm, Janitrol, Kenmore, Lennox, Luxaire, Maytag, Mitsubishi, Payne, Rheem, Ruud, Samsung, Sanyo, Sears, Sharp, Spartan, Tappan, Tempstar, Thermal Solutions, Trane, Utica, Weatherking, Westinghouse, Whirlpool, Williams, York, and Zephyr.
In the case of heated water or steam, piping is used to transport the heat to the rooms. Most modern hot water boiler heating systems have a circulator, which is a pump, to move hot water through the distribution system (as opposed to older gravity-fed systems). The heat can be transferred to the surrounding air using radiators, hot water coils (hydro-air), or other heat exchangers. The radiators may be mounted on walls or installed within the floor to produce floor heat.
Modern air conditioning systems are not designed to draw air into the room from the outside, they only recirculate the increasingly cool air on the inside. Because this inside air always has some amount of moisture suspended in it, the cooling portion of the process always causes ambient warm water vapor to condense on the cooling coils and to drip from them down onto a catch tray at the bottom of the unit from which it must then be routed outside, usually through a drain hole. As this moisture has no dissolved minerals in it, it will not cause mineral buildup on the coils. This will happen even if the ambient humidity level is low. If ice begins to form on the evaporative fins, it will reduce circulation efficiency and cause the development of more ice, etc. A clean and strong circulatory fan can help prevent this, as will raising the target cool temperature of the unit's thermostat to a point that the compressor is allowed to turn off occasionally. A failing thermistor may also cause this problem. Refrigerators without a defrost cycle may have this same issue. Dust can also cause the fins to begin blocking air flow with the same undesirable result: ice.
A reliable, efficient, and modern cooling system makes everyday life a whole lot better. Whether you’re in need of new installation, equipment replacement, seasonal maintenance, or repair in Chicagoland and the surrounding suburbs, Air Blue Heating and Cooling Inc. is the right answer. We bring you quality products and services that result in pure luxury without painful costs. As a Carrier Factory Authorized Dealer, we specialize in the most recognized, award-winning, and innovative air conditioners on the market. Along with precision temperature control, take advantage of unprecedented energy efficiency, whisper-quiet sound levels, and a range of features that enable greater control over your environment. Our team is fully licensed, bonded, insured, and NATE-certified. We make it easy to get the expert help you need with same-day service/installation, and 24/7 Emergency Service across Wheeling, Buffalo Grove, Northbrook, Deerfield, IL. When you contact Air Blue Heating and Cooling Inc., we don’t waste your time or money, leave behind mess or damage, or consider our job done until you are 100% satisfied. With over thirty years of practical experience, we are your local solution to perfect comfort.
As a Bryant Factory Authorized Dealer, Welzig Heating & Air consistently performs to strenuous standards of technical competence, business ethics, and customer approval. Our team is NATE-certified, factory trained and regularly updated in progressive technology. Equipped with leading edge equipment, tools, and a full inventory of genuine manufacturer’s replacement parts, we properly size and install new systems, accurately diagnose existing systems, and resolve the majority of issues right then and there.
Air Conditioner Repair Philadelphia trust, Heater Repair by Philadelphia’s top rated Heating and Cooling Company. HVAC Philly is a full service HVAC Repair services proudly serving residences and businesses in the Philadelphia, Bucks and Montgomery county area since 1994. At HVAC Philly we offer 24-hour emergency Air Conditioning Repair and Heating Repair service, as a greater Philadelphia licensed HVAC contractor, we install and service air conditioning and heating systems. In addition, we offer preventative maintenance plans, same day AC Repair, Heater replacement and custom ductwork.
Air flow meter Aquastat BACnet Blower door Building automation Carbon dioxide sensor Clean Air Delivery Rate (CADR) Gas sensor Home energy monitor Humidistat HVAC control system Intelligent buildings LonWorks Minimum efficiency reporting value (MERV) OpenTherm Programmable communicating thermostat Programmable thermostat Psychrometrics Room temperature Smart thermostat Thermostat Thermostatic radiator valve
Installing a split system may involve making modifications to the house itself for the necessary lines to be run. The heat exchangers are also more prone to picking up debris and must be cleaned on a regular basis. While they come with protective screens over the fan, care must still be taken to ensure that nothing gets in, especially in a home with children.
A little simple math can help determine the size system you need. A rule of thumb is 20 BTUs per square foot. So, a 500 square foot room would need 10,000 BTUs to cool or warm it efficiently. This assumes that you live in a temperate region and have adequate insulation with no energy loss. In the real world, all units have some degree of energy loss. This is reflected in an HVAC system's SEER rating for cooling and AFUE rating for heating.
HVAC System Quality Installation Contractor Checklist -- This checklist identifies all of the steps the contractor has taken for the Energy Star Certification and identifies what work the contractor has done. If the system is later modified, this checklist can help identify what was done to proper Energy Star specifications and what was added later that may not meet the requirements.
When a gas furnace is not in operation, most send a steady, wasteful draft of warm household air traveling up the venting system and out the roof. The Rheem Classic® Series and Classic® Plus Lines – with AFUE ratings of 78% and better – feature an induced-draft blower that works in conjunction with a hot surface ignition system to pull hot gases through the heat exchanger at a constant and controlled rate of flow. As the burner cycles off, the draft blower stops, keeping the heating air in the system.
Ground source, or geothermal, heat pumps are similar to ordinary heat pumps, but instead of transferring heat to or from outside air, they rely on the stable, even temperature of the earth to provide heating and air conditioning. Many regions experience seasonal temperature extremes, which would require large-capacity heating and cooling equipment to heat or cool buildings. For example, a conventional heat pump system used to heat a building in Montana's −70 °F (−57 °C) low temperature or cool a building in the highest temperature ever recorded in the US—134 °F (57 °C) in Death Valley, California, in 1913 would require a large amount of energy due to the extreme difference between inside and outside air temperatures. A few feet below the earth's surface, however, the ground remains at a relatively constant temperature. Utilizing this large source of relatively moderate temperature earth, a heating or cooling system's capacity can often be significantly reduced. Although ground temperatures vary according to latitude, at 6 feet (1.8 m) underground, temperatures generally only range from 45 to 75 °F (7 to 24 °C).
When our Denver heating company provides you with maintenance checks before the cold of winter sets in, you will be saving money in several different ways. One of the benefits of a maintenance plan is our technicians will be less likely to have to make repairs throughout the year as long as the system is properly maintained. Our Denver heating company will have your system running at its most efficient, helping to reduce your utility bills each month. An added benefit of a more efficiently running system is the positive environmental effect that it will have.
We are service professionals! As licensed contractors and specialists in the field of heating and air conditioning, we have the tools, the equipment, and the experience to keep your equipment running smoothly all year long. If it is emergency service that you need we are available to assist you! To help reduce service emergencies, we offer service agreements to keep your comfort system running at peak performance.
When we’re in a customer’s home, we’re always on the lookout for things we can do to help them out and put a smile on their face. It could be as simple as changing a lightbulb or as involved as cleaning gutters, listing a car for sale online, or repairing a broken gate. There’s no limit to what we might do, and of course, there’s never any charge to help out. It’s good deeds for FREE!
The first air conditioners and refrigerators employed toxic or flammable gases, such as ammonia, methyl chloride, or propane, that could result in fatal accidents when they leaked. Thomas Midgley, Jr. created the first non-flammable, non-toxic chlorofluorocarbon gas, Freon, in 1928. The name is a trademark name owned by DuPont for any chlorofluorocarbon (CFC), hydrochlorofluorocarbon (HCFC), or hydrofluorocarbon (HFC) refrigerant. The refrigerant names include a number indicating the molecular composition (e.g., R-11, R-12, R-22, R-134A). The blend most used in direct-expansion home and building comfort cooling is an HCFC known as chlorodifluoromethane (R-22).
A packaged system is a single unit combining all the components described in the split system. Since the unit is a package, it must be placed outside the building and indoor air is “ducted” from the building to the packaged system and back through an air distribution system. These units typically have SEER rating from 10 to 18. If heating is required, an alternate method of heating the interior of the building must be used, usually in the form of electric or gas heating.