The icing problem becomes much more severe with lower outdoor temperatures, so heat pumps are commonly installed in tandem with a more conventional form of heating, such as a natural gas or oil furnace, which is used instead of the heat pump during harsher winter temperatures. In this case, the heat pump is used efficiently during the milder temperatures, and the system is switched to the conventional heat source when the outdoor temperature is lower.
Before selecting the installation location of air conditioner, several main factors need to be considered. First of all, the direction of air flow from the indoor units should not fall on the place of rest or work area. Secondly, there should not be any obstacles on the way of the airflow that might prevent it from covering the space of the premises as much as possible. The outdoor unit must also be located in an open space, otherwise the heat from the house will not be effectively discharged outside and the productivity of the entire system will drop sharply. It is highly advisable to install the air conditioner units in easily accessible places, for further maintenance during operation.

Honesty and integrity go a long way with me also pricing was very fair.....A-ok gets it done.... My a/c just stopped working after 12 a.m. I called 3 companies and no one was able to come out till the morning. I couldn't wait till morning due to the fact I have elderly people living with me. so I call A-ok and Tyler was the tech on call for the night. He was super helpful and friendly. Tyler was a few counties away but made the call to rush to my home after 12 am. And fix my unit. It was getting pretty hot inside my house. Turns out it was just a fuse that went bad. He was able to correct it in minutes. I'm thankful Tyler is a honest young man. He could have said anything to run up the bill but he didn't... it was just a blown fuse. I high recommend A-OK for service needs. The pricing was fair and matched up better than everyone else.... the difference which is huge was Tyler came out to do the repair where as every other company wanted me to wait till the morning. Thank you Tyler for getting my unit back in order and I'm happy to say they have my Business going forward....
The main problem when installing a multi-split system is the laying of long refrigerant lines for connecting the external unit to the internal ones. While installing a separate split system, workers try to locate both units opposite to each other, where the length of the line is minimal. Installing a multi-split system creates more difficulties, since some of indoor units can be located far from the outside. The first models of multi-split systems had one common control system that did not allow you to set the air conditioning individually for each room. However, now the market has a wide selection of multi-split systems, in which the functional characteristics of indoor units operate separately from each other.
What happens when you have an emergency? The first reaction of most people is to panic. When a furnace stops working, you need it fixed and fixed immediately—especially in the middle of a cold, Ohio winter. That need can make people feel as if they are at the mercy of the repair company. That is why it is so important to call a company you can trust and rely on—Jennings Heating and Cooling.

We are totally committed to your comfort. Our quality technicians set our business apart by providing the best and most professional service in the area. We are fully trained on today’s HVAC technology systems and methods, so when we are in your home or business, you can rest assured that we’ll work quickly and skillfully toward your total comfort.
In the case of direct expansion equipment, the air passing over the indoor cooling coil heats the cold liquid refrigerant. Heating the refrigerant causes boiling and transforms the refrigerant from a cold liquid to a warm gas. This warm gas (or vapor) is pumped from the cooling coil to the compressor through a copper tube (suction line to the compressor) where the warm gas is compressed. In some cases, an accumulator is placed between the cooling coil and the compressor to capture unused liquid refrigerant and ensures that only vapor enters the compressor. The compression process increases the pressure of the refrigerant vapor and significantly increases the temperature of the vapor. The compressor pumps the vapor through another heat exchanger (outdoor condenser) where heat is rejected and the hot gas is condensed to a warm high pressure liquid. This warm high pressure liquid is pumped through a smaller copper tube (liquid line) to a filter (or filter/dryer) and then on to an expansion device where the high pressure liquid is reduced to a cold, low pressure liquid. The cold liquid enters the indoor cooling coil and the process repeats.

Refrigeration air conditioning equipment usually reduces the absolute humidity of the air processed by the system. The relatively cold (below the dewpoint) evaporator coil condenses water vapor from the processed air, much like an ice-cold drink will condense water on the outside of a glass. Therefore, water vapor is removed from the cooled air and the relative humidity in the room is lowered. The water is usually sent to a drain or may simply drip onto the ground outdoors. The heat is rejected by the condenser which is located outside of room to be cooled.
Keep in mind that ducts used for heating might not be the right size or in the right location for optimal cooling. Your contractor should ensure that duct sections are properly sized and that there are enough supply registers to deliver sufficient air to the right spots. Undersized ductwork can make for inefficient and noisy operation. Here’s how to keep yours humming:
The warm air inside your home is drawn into the system through return ducts and then go over a refrigerant coil. As the warm air is blown across the cooled coil, heat is removed. Refrigerant lines then carry the heat outside. Now you’re left with cool, comfortable indoor air that you can enjoy on the hottest of days. And that’s pretty much it. Sure, the equipment is more complex than that, but the process itself is easy to break down and comprehend.
The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.

There are multiple reasons to replace your HVAC system. If you have built additions onto your house, you may find your old system no longer meets the requirements for the new dimensions. Perhaps a new technological breakthrough has provided features that will improve your comfort and air quality. Most often, however, you need to replace your system because it no longer works properly.

Natural ventilation is the ventilation of a building with outside air without using fans or other mechanical systems. It can be via operable windows, louvers, or trickle vents when spaces are small and the architecture permits. In more complex schemes, warm air is allowed to rise and flow out high building openings to the outside (stack effect), causing cool outside air to be drawn into low building openings. Natural ventilation schemes can use very little energy, but care must be taken to ensure comfort. In warm or humid climates, maintaining thermal comfort solely via natural ventilation might not be possible. Air conditioning systems are used, either as backups or supplements. Air-side economizers also use outside air to condition spaces, but do so using fans, ducts, dampers, and control systems to introduce and distribute cool outdoor air when appropriate.


Relax—ABC Plumbing, Heating, Cooling & Electric is here for you when you need us most! Our highly trained, background-checked technicians perform heating and air conditioning repairs quickly and efficiently to keep your family warm and cozy all winter long. With over 65 years of experience, you can trust that we’ll fix your furnace correctly the first time.
Some of the most common problems that require gas furnace repair include malfunctioning thermostats, frequent cycling, blowers that continuously run, excessive noise, general lack of maintenance, dirty filters and electric ignition or pilot control problems. Repair Clinic can show you how to fix your furnace and save you money on the parts and repair. Safety first! Be sure to consult an HVAC pro if you’re not confident making furnace repairs.
For more than 30 years, Northeastern PA homeowners have trusted T.E. Spall & Son for heating, air conditioning, and plumbing in Scranton, Wilkes-Barre, and the surrounding areas. Our team of highly trained, professional HVAC contractors and plumbers is committed to providing you with the best heating and cooling services possible. Your satisfaction and comfort are always our number one priorities!
Baker Brothers Air Conditioning company offers residential HVAC services including a/c and air conditioning repair, a/c and air conditioning replacement, a/c and air conditioning installation, a/c and air conditioning tune up, a/c and air conditioning inspections, a/c and air conditioning maintenance on air conditioning units and systems in most or all of the following Dallas, TX ZIP Codes: 75229, 75230, 75225, 75220, 75209, 75219, 75247, 75212, 75235, 75201, 75207, 75248, 75287, 75252, 75244, 75254, 75240, 75251, 75248-1713, 75214, 75228, 75243, 75238, 75218, 75206, 75231, 75204, 75226, 75246, 75227, 75208, 75217, 75232, 75224, 75211, 75241, 75215, 75233, 75253, 75216, 75223, 75237, 75249, 75203, 75210
Air Conditioning Your home's air conditioner is an essential part of your overall indoor comfort. A properly working system can mean the difference between a cool, comfortable summer and a hot, miserable few months. If you're currently dealing with a broken air conditioner, an inefficient system, or you would like to schedule a routine, pre-season tune-up, Horizon Services is here to help!
Furnace Circuit Board -- The furnace circuit board controls a variety of functions. It not only handles the regular operation of the furnace, it also monitors the furnace's various safety circuits. Over time, vibrations from the furnace can weaken solder point and cause them to separate. Dirt and debris can cause short-circuits that damage the board. Failure of the circuit board can cause a variety of effects ranging from the fan not turning on to the complete shutdown of the furnace.
×