As one of the premier heating & cooling companies in St. Louis, Vogel has dedicated our business to serving our customers with the utmost quality in HVAC services for both residential and commercial entities alike. We strive to build out a culture within our team that delivers the kind of experience you deserve when working with a service provider. The qualities that are most important to you, are most important to us - convenience, trustworthiness, good value, impeccable quality, and our willingness to stand behind our successes and learn from our mistakes. We invite you to explore our site, see what customers say, and give us a call.
A little simple math can help determine the size system you need. A rule of thumb is 20 BTUs per square foot. So, a 500 square foot room would need 10,000 BTUs to cool or warm it efficiently. This assumes that you live in a temperate region and have adequate insulation with no energy loss. In the real world, all units have some degree of energy loss. This is reflected in an HVAC system's SEER rating for cooling and AFUE rating for heating.
A more efficient method of controlling humidity is to use the waste heat from the refrigeration cycle itself. Instead of rejecting the waste heat outdoors, the heat is directed inside when humidity control is required. One form of heat reclaim is called hot-gas reheat or “refrigerant desuperheating” where refrigerant is passed through a heat exchanger located downstream of the cooling coil. The hot high pressure vapor leaving the compressor passes through this heat exchanger prior to entering the condenser coil. This in turn heats the indoor air and again causes the AC system to run longer to meet the thermostat set point. Although more energy is used, this is much more efficient than turning on an electric heater. Another form of heat reclaim is called sub-cool reheat. This strategy takes the warm liquid refrigerant from the condenser and passes it through a heat exchanger located downstream of the cooling coil. Less heat is available using this method because the majority of the heat has already been rejected at the condenser. Since more energy is used to pump liquid (as opposed to a gas) through the heat exchanger it would appear that this method is less efficient than the hot-gas method, however, the liquid in the heat exchanger is sub-cooled in the cold supply air stream which increases the capacity of the air conditioner. Since more capacity is available, the AC units is able to meet the thermostat more quickly.

Our Baker Brothers Family Plan membership provides you with an annual inspection of your furnace. This will help keep it working properly so it’s there for you when you need it most. Preventative maintenance is the best way to ensure your system is working as efficient as possible and not costing you more than it needs to on your monthly utility bills.
The heat pump gained popularity in the 1950s in Japan and the United States.[13] Heat pumps can extract heat from various sources, such as environmental air, exhaust air from a building, or from the ground. Initially, heat pump HVAC systems were only used in moderate climates, but with improvements in low temperature operation and reduced loads due to more efficient homes, they are increasing in popularity in cooler climates.
For a scheduled or emergency HVAC repair, you can count on SMO Energy and our team of certified technicians. We’re ready 24 hours a day and seven days a week to fix your heating system and deliver the professional and courteous service you expect from our family-owned and operated business. Aside from your system shutting down, several other signs that your HVAC system needs repairs include:
To qualify as a Certified Daikin Comfort Pro Dealer, Green Valley Cooling & Heating maintains exceptionally high standards of business practices, technical expertise, and customer approval ratings.  Our loyal customers, amazing community of support, dedicated team members, and vendors have all contributed to celebrating 50 years in business, and we see it as a benchmark for future achievement. Rest assured, at Green Valley Cooling & Heating we continue find new ways to exceed your expectations.
Central, "all-air" air-conditioning systems (or package systems) with a combined outdoor condenser/evaporator unit are often installed in North American residences, offices, and public buildings, but are difficult to retrofit (install in a building that was not designed to receive it) because of the bulky air ducts required. (Minisplit ductless systems are used in these situations.) Outside of North America, packaged systems are only used in limited applications involving large indoor space such as stadiums, theatres or exhibition halls.

Bonney’s NATE certified technicians will troubleshoot and repair your furnace for safe and reliable operation. Our technicians use state of the art tools including video inspection cameras and exhaust gas analyzers to perform thorough, comprehensive diagnostics when equipment is broken. Furthermore, we arrive in a “warehouse on wheels” stocked with many parts to get your furnace repaired as quickly as possible.  For an unexpected heater repair Bonney offers financing to make your comfort affordable.


Although HVAC is executed in individual buildings or other enclosed spaces (like NORAD's underground headquarters), the equipment involved is in some cases an extension of a larger district heating (DH) or district cooling (DC) network, or a combined DHC network. In such cases, the operating and maintenance aspects are simplified and metering becomes necessary to bill for the energy that is consumed, and in some cases energy that is returned to the larger system. For example, at a given time one building may be utilizing chilled water for air conditioning and the warm water it returns may be used in another building for heating, or for the overall heating-portion of the DHC network (likely with energy added to boost the temperature).[4][5][6]

Engineers have pointed out some areas where efficiency of the existing hardware could be improved. For example, the fan blades used to move the air are usually stamped from sheet metal, an economical method of manufacture, but as a result they are not aerodynamically efficient. A well-designed blade could reduce electrical power required to move the air by a third.[26]
Our NATE-certified technicians are always available, 24 hours a day and 365 days a year, to resolve emergency situations quickly and accurately.  Our team participates in factory-sponsored training updates, utilizes leading-edge diagnostic equipment, and follows strict installation and service procedures.  Every single Green Valley Cooling & Heating technician is clean air certified.  Rest assured, when you contact Green Valley Cooling & Heating, your call is answered by a skilled and experienced professional, who puts your best interests first.
Poorly maintained water cooling towers can promote the growth and spread of microorganisms,[55] such as Legionella pneumophila, the infectious agent responsible for Legionnaires' disease, or thermophilic actinomycetes. As long as the cooling tower is kept clean (usually by means of a chlorine treatment), these health hazards can be avoided or reduced. Excessive air conditioning can have a negative effect on skin, causing it to dry out, and can also cause dehydration.[citation needed]
If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
There’s nothing like a warm indoor space to take the sting out of a blustery winter day, but there’s nothing worse than a heater that quits just when you need it most. Losing heat for any length of time can be inconvenient at best and dangerous at worst. Fortunately, when you partner with Cool Care Heating & Air, you can rest assured that whether you need emergency heating repair or annual furnace maintenance, we’ll go all out to keep you comfortable. Cool Care Heating & Air is a Bryant Factory Authorized Dealer, so you can always count on prompt service, a courteous attitude, reasonable prices and top-shelf products.
For most homeowners, any HVAC repair needs to be done in a timely manner. The longer you have to wait for AC repair, furnace repair, etc., the more difficult you will find it to maintain a comfortable temperature in your residence. Our experienced technicians will find the problem and complete air conditioner or furnace repair quickly. Instead of having to suffer through a cold winter or hot summer due to HVAC problems, contact Deljo Heating & Cooling.
Here at Baker Brothers, we know just how unbearable the heat in the DFW metroplex can be. That’s why we want your home’s air conditioning unit to be functioning properly. Whether you have a problem that you want to be solved now or just want to do preventative maintenance, we can help. Contact us today to schedule your HVAC service or repair in the Dallas & Fort Worth area!
A vapour seal is an essential part of preventing moisture infiltration into or migration out of a critical space, such as a data processing centre or other room that contains sensitive electronic instrumentation.  Essentially, a vapour seal is a barrier that prevents air, moisture, and contaminants from migrating through tiny cracks or pores in the walls, floor, and ceiling into the critical space.  It is also used extensively on pipe insulation to prevent moisture ingress that may cause deterioration of the insulation or freezing in cold conditions.
Have your contractor do a load calculation based on a recognized method, such as one in Manual J from the ACCA. The contractor’s evaluation should include whether your ducts need to be resized, sealed and insulated, or replaced. Remember that an indoor evaporator coil and outdoor condenser must be a matched set from the same brand, or the performance, efficiency, and capacity might not meet expectations.

The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.
Today’s heaters are technological wonders that will keep you warm and save you money. Investing in an energy-efficient heating system can raise the value of your property, and the cost of installation will be realized on the amount you’ll save on utility bills. With Cool Care Heating & Air, you can count on proper sizing and a hassle-free installation process. The new unit may also qualify for energy-efficient incentives, and Cool Care Heating & Air offers periodic dealer rebates on select replacement systems. If your heating system is 10-15 years old, needs frequent repair work and isn’t keeping you as warm as it used to, it’s probably approaching the end of its lifespan. Replacing the unit before it dies altogether can save you time, trouble and money.
Though Harrison had commercial success establishing a second ice company back in Sydney in 1860, he later entered the debate over how to compete against the American advantage of ice-refrigerated beef sales to the United Kingdom. He wrote: "Fresh meat frozen and packed as if for a voyage, so that the refrigerating process may be continued for any required period", and in 1873 prepared the sailing ship Norfolk for an experimental beef shipment to the United Kingdom. His choice of a cold room system instead of installing a refrigeration system upon the ship itself proved disastrous when the ice was consumed faster than expected.[citation needed]
Humidity is becoming more of a concern to building operators and owners. High indoor humidity leads to mold and mildew growth inside the building. The are several methods of controlling indoor humidity. The simplest (and most expensive) method is to connect a humidistat to an electric heater. When the humidity inside the building rises above the humidistat set point, the heater is turned on. The additional heat causes the air conditioning system to run longer and remove more moisture.
×